[220]HELLO! BOOT0 is starting May 13 2020 14:10:04!
[225]BOOT0 commit : 593cf83
[228]set pll start
[231]periph0 has been enabled
[234]set pll end
[236]unknow PMU
[237]PMU: AXP806
[245]vaild para:1 select dram para0
[248]board init ok
[250]DRAM BOOT DRIVE INFO: V0.52
[253]the chip id is 0x5000
[256]chip id check OK
[258]DRAM_VCC set to 1500 mv
[262]read_calibration error
[266]read_calibration error
[270]read_calibration error
[274]read_calibration error
[278]read_calibration error
[282]read_calibration error
[286]read_calibration error
[290]read_calibration error
[294]read_calibration error
[298]read_calibration error
[300]retraining final error
[305][AUTO DEBUG]32bit,1 ranks training success!
[312]DRAM CLK =720 MHZ
[315]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[321]Actual DRAM SIZE =1024 M
[324]DRAM SIZE =1024 MBytes,
para1 = 30fa,
para2 = 4000000,
dram_tpr13 = 6041
[337]DRAM simple test OK.
[339]rtc standby flag is 0x0, super standby flag is 0x0
[345]dram size =1024
[347]*****dram handle ok****
[350]key press :
[352]card no is 0
[354]sdcard 0 line count 4
[357][mmc]: mmc driver ver 2019-12-19 10:41
[361][mmc]: sdc0 spd mode error, 2
[365][mmc]: set f_max to 50M, set f_max_ddr to 25M
[370][mmc]: mmc 0 bias 0
[377][mmc]: Wrong media type 0x0
[381][mmc]: ***Try SD card 0***
[400][mmc]: HSSDR52/SDR25 4 bit
[403][mmc]: 50000000 Hz
[405][mmc]: 30436 MB
[407][mmc]: ***SD/MMC 0 init OK!!!***
[506]Loading boot-pkg Succeed(index=0).
[510]Entry_name = u-boot
[519]Entry_name = monitor
[523]Entry_name = dtbo
[526]Entry_name = dtb
[529]Jump to second Boot.
NOTICE: BL3-1: v1.0(debug):9fecd83
NOTICE: BL3-1: Built : 17:08:29, 2020-05-28
NOTICE: BL3-1 commit: 8
ERROR: Error initializing runtime service tspd_fast
NOTICE: BL3-1: Preparing for EL3 exit to normal world
NOTICE: BL3-1: Next image address = 0x4a000000
-OTICE: BL3-1: Next image spsr = 0x1d3

U-Boot 2018.05 (Oct 22 2020 - 17:24:26 +0800)
Allwinner Technology

[00.604]CPU: Allwinner Family
[00.607]Model: sun50iw9
I2C: ready
[00.611]DRAM: 1 GiB
[00.614]Relocation Offset is: 35ec5000
[00.652]secure enable bit: 0
[00.655]pmu_axp152_probe pmic_bus_read fail
[00.659]PMU: AXP806
[00.664]CPU=1008 MHz,PLL6=600 Mhz,
AHB=200 Mhz, APB1=100Mhz MBus=400Mhz
[00.825]sunxi overlay merged okqv
[00.829]drv_disp_init
[00.858]__clk_enable: clk is null.
[00.863]drv_disp_init finish
[00.866]gic: sec monitor mode
[00.890]flash init start
[00.892]workmode = 0,storage type = 1
[00.896]MMC: 0
[00.897]get mem for descripter OK !

card_caps:0x3000000a
host_caps:0x3000003f
[00.935]sunxi flash init ok
[00.939]Loading Environment from SUNXI_FLASH... OK
[00.954]Item0 (Map) magic is bad
[00.957]the secure storage item0 copy0 is bad
[00.961]Item0 (Map) magic is bad
[00.964]Item0 (Map) magic is bad
[00.967]usb burn from boot
delay time 0
weak:otg_phy_config
[00.980]usb prepare ok
[01.783]overtime
[01.787]do_burn_from_boot usb : no usb exist
[01.791]boot_gui_init:start
** Unable to read file test.fex **
[01.926]boot_gui_init:finish
[01.930]bmp_name=bootlogo.bmp
1152056 bytes read in 49 ms (22.4 MiB/s)
[01.996]update dts
** Unrecognized filesystem type **
[02.012]load file(ULI/factory/rootwait init.txt) error.
** Unrecognized filesystem type **
[02.031]load file(ULI/factory/snum.txt) error.
** Unrecognized filesystem type **
[02.050]load file(ULI/factory/mac.txt) error.
** Unrecognized filesystem type **
[02.068]load file(ULI/factory/wifi_mac.txt) error.
** Unrecognized filesystem type **
[02.087]load file(ULI/factory/bt_mac.txt) error.
** Unrecognized filesystem type **
[02.105]load file(ULI/factory/selinux.txt) error.
** Unrecognized filesystem type **
[02.124]load file(ULI/factory/specialstr.txt) error.
[02.144]update part info
[02.164]update bootcmd
[02.166]No ethernet found.
Hit any key to stop autoboot: 0
=>

---