отображение / управление настройками ETS (Enhanced Transmission Selection) подсистемы DCB (Data Center Bridging) (show / manipulate ETS (Enhanced Transmission Selection) settings of the DCB (Data Center Bridging) subsystem)
Имя (Name)
dcb-ets - show / manipulate ETS (Enhanced Transmission Selection)
settings of the DCB (Data Center Bridging) subsystem
Синопсис (Synopsis)
dcb [ OPTIONS ] ets { COMMAND | help }
dcb ets show dev DEV [ willing ] [ ets-cap ] [ cbs ] [ tc-tsa ] [
reco-tc-tsa ] [ pg-bw ] [ tc-bw ] [ reco-tc-bw ] [ prio-
tc ] [ reco-prio-tc ]
dcb ets set dev DEV [ willing { on | off } ] [ { tc-tsa | reco-
tc-tsa } TSA-MAP ] [ { pg-bw | tc-bw | reco-tc-bw } BW-
MAP ] [ { prio-tc | reco-prio-tc } PRIO-MAP ]
TSA-MAP := [ TSA-MAP ] TSA-MAPPING
TSA-MAPPING := { TC | all }:{ strict | cbs | ets | vendor }
BW-MAP := [ BW-MAP ] BW-MAPPING
BW-MAPPING := { TC | all }:INTEGER
PRIO-MAP := [ PRIO-MAP ] PRIO-MAPPING
PRIO-MAPPING := { PRIO | all }:TC
TC := { 0 .. 7 }
PRIO := { 0 .. 7 }
Описание (Description)
dcb ets is used to configure Enhanced Transmission Selection
attributes through Linux DCB (Data Center Bridging) interface.
ETS permits configuration of mapping of priorities to traffic
classes, traffic selection algorithm to use per traffic class,
bandwidth allocation, etc.
Two DCB TLVs are related to the ETS feature: a configuration and
recommendation values. Recommendation values are named with a
prefix reco-, while the configuration ones have plain names.
Параметры (Parameters)
For read-write parameters, the following describes only the write
direction, i.e. as used with the set command. For the show
command, the parameter name is to be used as a simple keyword
without further arguments. This instructs the tool to show the
value of a given parameter. When no parameters are given, the
tool shows the complete ETS configuration.
ets-cap
A read-only property that shows the number of supported
ETS traffic classes.
cbs A read-only property that is enabled if the driver and the
hardware support the CBS Transmission Selection Algorithm.
willing { on | off }
Whether local host should accept configuration from peer
TLVs.
prio-tc PRIO-MAP
reco-prio-tc PRIO-MAP
PRIO-MAP uses the array parameter syntax, see dcb(8) for
details. Keys are priorities, values are traffic classes.
For each priority sets a TC where traffic with that
priority is directed to.
tc-tsa TSA-MAP
reco-tc-tsa TSA-MAP
TSA-MAP uses the array parameter syntax, see dcb(8) for
details. Keys are TCs, values are Transmission Selection
Algorithm (TSA) keywords described below. For each TC sets
an algorithm used for deciding how traffic queued up at
this TC is scheduled for transmission. Supported TSAs are:
strict - for strict priority, where traffic in higher-
numbered TCs always takes precedence over traffic in
lower-numbered TCs.
ets - for Enhanced Traffic Selection, where available
bandwidth is distributed among the ETS-enabled TCs
according to the weights set by tc-bw and reco-tc-bw,
respectively.
cbs - for Credit Based Shaper, where traffic is scheduled
in a strict manner up to the limit set by a shaper.
vendor - for vendor-specific traffic selection algorithm.
tc-bw BW-MAP
reco-tc-bw BW-MAP
BW-MAP uses the array parameter syntax, see dcb(8) for
details. Keys are TCs, values are integers representing
percent of available bandwidth given to the traffic class
in question. The value should be 0 for TCs whose TSA is
not ets, and the sum of all values shall be 100. As an
exception to the standard wording, a configuration with no
ets TCs is permitted to sum up to 0 instead.
pg-bw BW-MAP
The precise meaning of pg-bw is not standardized, but the
assumption seems to be that the same scheduling process as
on the transmit side is applicable on receive side as
well, and configures receive bandwidth allocation for ets
ingress traffic classes (priority groups).
Примеры (Examples)
Configure ETS priomap in a one-to-one fashion:
# dcb ets set dev eth0 prio-tc 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
Set TSA and transmit bandwidth configuration:
# dcb ets set dev eth0 tc-tsa all:strict 0:ets 1:ets 2:ets \
tc-bw all:0 0:33 1:33 2:34
Show what was set:
# dcb ets show dev eth0 prio-tc tc-tsa tc-bw
prio-tc 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
tc-tsa 0:ets 1:ets 2:ets 3:strict 4:strict 5:strict 6:strict
7:strict
tc-bw 0:33 1:33 2:34 3:0 4:0 5:0 6:0 7:0
Статус выхода (Exit)
Exit status is 0 if command was successful or a positive integer
upon failure.
Смотри также (See also)
dcb(8)
Сообщение об ошибках (Reporting bugs)
Report any bugs to the Network Developers mailing list
<netdev@vger.kernel.org> where the development and maintenance is
primarily done. You do not have to be subscribed to the list to
send a message there.
