настроить устройства PCI (configure PCI devices)
Имя (Name)
setpci - configure PCI devices
Синопсис (Synopsis)
setpci [options] devices operations...
Описание (Description)
setpci is a utility for querying and configuring PCI devices.
All numbers are entered in hexadecimal notation.
Root privileges are necessary for almost all operations,
excluding reads of the standard header of the configuration space
on some operating systems. Please see lspci(8) for details on
access rights.
Параметры (Options)
General options
-v Tells setpci to be verbose and display detailed
information about configuration space accesses.
-f Tells setpci not to complain when there's nothing to do
(when no devices are selected). This option is intended
for use in widely-distributed configuration scripts where
it's uncertain whether the device in question is present
in the machine or not.
-D `Demo mode' -- don't write anything to the configuration
registers. It's useful to try setpci -vD to verify that
your complex sequence of setpci operations does what you
think it should do.
-r Avoids bus scan if each operation selects a specific
device (uses the -s selector with specific domain, bus,
slot, and function). This is faster, but if the device
does not exist, it fails instead of matching an empty set
of devices.
--version
Show setpci version. This option should be used stand-
alone.
--help Show detailed help on available options. This option
should be used stand-alone.
--dumpregs
Show a list of all known PCI registers and capabilities.
This option should be used stand-alone.
PCI access options
The PCI utilities use the PCI library to talk to PCI devices (see
pcilib(7) for details). You can use the following options to
influence its behavior:
-A <method>
The library supports a variety of methods to access the
PCI hardware. By default, it uses the first access method
available, but you can use this option to override this
decision. See -A help for a list of available methods and
their descriptions.
-O <param>=<value>
The behavior of the library is controlled by several named
parameters. This option allows one to set the value of
any of the parameters. Use -O help for a list of known
parameters and their default values.
-H1 Use direct hardware access via Intel configuration
mechanism 1. (This is a shorthand for -A intel-conf1.)
-H2 Use direct hardware access via Intel configuration
mechanism 2. (This is a shorthand for -A intel-conf2.)
-G Increase debug level of the library.
DEVICE SELECTION
Before each sequence of operations you need to select which
devices you wish that operation to affect.
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
Consider only devices in the specified domain (in case
your machine has several host bridges, they can either
share a common bus number space or each of them can
address a PCI domain of its own; domains are numbered from
0 to ffff), bus (0 to ff), slot (0 to 1f) and function (0
to 7). Each component of the device address can be
omitted or set to "*", both meaning "any value". All
numbers are hexadecimal. E.g., "0:" means all devices on
bus 0, "0" means all functions of device 0 on any bus,
"0.3" selects third function of device 0 on all buses and
".4" matches only the fourth function of each device.
-d [<vendor>]:[<device>]
Select devices with specified vendor and device ID. Both
ID's are given in hexadecimal and may be omitted or given
as "*", both meaning "any value".
When -s and -d are combined, only devices that match both
criteria are selected. When multiple options of the same kind are
specified, the rightmost one overrides the others.
Операции (Operations)
There are two kinds of operations: reads and writes. To read a
register, just specify its name. Writes have the form
name=value,value... where each value is either a hexadecimal
number or an expression of type data:mask where both data and
mask are hexadecimal numbers. In the latter case, only the bits
corresponding to binary ones in the mask are changed
(technically, this is a read-modify-write operation).
There are several ways how to identity a register:
• Tell its address in hexadecimal.
• Spell its name. Setpci knows the names of all registers in
the standard configuration headers. Use `setpci
--dumpregs' to get the complete list. See PCI bus
specifications for the precise meaning of these registers
or consult header.h or /usr/include/pci/pci.h for a brief
sketch.
• If the register is a part of a PCI capability, you can
specify the name of the capability to get the address of
its first register. See the names starting with `CAP_' or
`ECAP_' in the --dumpregs output.
• If the name of the capability is not known to setpci, you
can refer to it by its number in the form CAPid or ECAPid,
where id is the numeric identifier of the capability in
hexadecimal.
• Each of the previous formats can be followed by +offset to
add an offset (a hex number) to the address. This feature
can be useful for addressing of registers living within a
capability, or to modify parts of standard registers.
• To choose how many bytes (1, 2, or 4) should be
transferred, you should append a width specifier .B, .W,
or .L. The width can be omitted if you are referring to a
register by its name and the width of the register is well
known.
• Finally, if a capability exists multiple times you can
choose which one to target using @number. Indexing starts
at 0.
All names of registers and width specifiers are case-insensitive.
EXAMPLES
COMMAND
asks for the word-sized command register.
4.w is a numeric address of the same register.
COMMAND.l
asks for a 32-bit word starting at the location of the
command register, i.e., the command and status registers
together.
VENDOR_ID+1.b
specifies the upper byte of the vendor ID register
(remember, PCI is little-endian).
CAP_PM+2.w
corresponds to the second word of the power management
capability.
ECAP108.l
asks for the first 32-bit word of the extended capability
with ID 0x108.
Смотри также (See also)
lspci(8), pcilib(7)
