перезагрузить или включить / выключить Ctrl-Alt-Del (reboot or enable/disable Ctrl-Alt-Del)
Имя (Name)
reboot - reboot or enable/disable Ctrl-Alt-Del
Синопсис (Synopsis)
/* Since kernel version 2.1.30 there are symbolic names LINUX_REBOOT_*
for the constants and a fourth argument to the call: */
#include <linux/reboot.h> /* Definition of LINUX_REBOOT_* constants */
#include <sys/syscall.h> /* Definition of SYS_* constants */
#include <unistd.h>
int syscall(SYS_reboot, int magic, int magic2, int cmd, void *arg);
/* Under glibc and most alternative libc's (including uclibc, dietlibc,
musl and a few others), some of the constants involved have gotten
symbolic names RB_*, and the library call is a 1-argument
wrapper around the system call: */
#include <sys/reboot.h> /* Definition of RB_* constants */
#include <unistd.h>
int reboot(int cmd);
Описание (Description)
The reboot() call reboots the system, or enables/disables the
reboot keystroke (abbreviated CAD, since the default is Ctrl-Alt-
Delete; it can be changed using loadkeys(1)).
This system call fails (with the error EINVAL) unless magic
equals LINUX_REBOOT_MAGIC1 (that is, 0xfee1dead) and magic2
equals LINUX_REBOOT_MAGIC2 (that is, 672274793). However, since
2.1.17 also LINUX_REBOOT_MAGIC2A (that is, 85072278) and since
2.1.97 also LINUX_REBOOT_MAGIC2B (that is, 369367448) and since
2.5.71 also LINUX_REBOOT_MAGIC2C (that is, 537993216) are
permitted as values for magic2. (The hexadecimal values of these
constants are meaningful.)
The cmd argument can have the following values:
LINUX_REBOOT_CMD_CAD_OFF
(RB_DISABLE_CAD, 0). CAD is disabled. This means that
the CAD keystroke will cause a SIGINT signal to be sent to
init (process 1), whereupon this process may decide upon a
proper action (maybe: kill all processes, sync, reboot).
LINUX_REBOOT_CMD_CAD_ON
(RB_ENABLE_CAD, 0x89abcdef). CAD is enabled. This means
that the CAD keystroke will immediately cause the action
associated with LINUX_REBOOT_CMD_RESTART.
LINUX_REBOOT_CMD_HALT
(RB_HALT_SYSTEM, 0xcdef0123; since Linux 1.1.76). The
message "System halted." is printed, and the system is
halted. Control is given to the ROM monitor, if there is
one. If not preceded by a sync(2), data will be lost.
LINUX_REBOOT_CMD_KEXEC
(RB_KEXEC, 0x45584543, since Linux 2.6.13). Execute a
kernel that has been loaded earlier with kexec_load(2).
This option is available only if the kernel was configured
with CONFIG_KEXEC.
LINUX_REBOOT_CMD_POWER_OFF
(RB_POWER_OFF, 0x4321fedc; since Linux 2.1.30). The
message "Power down." is printed, the system is stopped,
and all power is removed from the system, if possible. If
not preceded by a sync(2), data will be lost.
LINUX_REBOOT_CMD_RESTART
(RB_AUTOBOOT, 0x1234567). The message "Restarting
system." is printed, and a default restart is performed
immediately. If not preceded by a sync(2), data will be
lost.
LINUX_REBOOT_CMD_RESTART2
(0xa1b2c3d4; since Linux 2.1.30). The message "Restarting
system with command '%s'" is printed, and a restart (using
the command string given in arg) is performed immediately.
If not preceded by a sync(2), data will be lost.
LINUX_REBOOT_CMD_SW_SUSPEND
(RB_SW_SUSPEND, 0xd000fce1; since Linux 2.5.18). The
system is suspended (hibernated) to disk. This option is
available only if the kernel was configured with
CONFIG_HIBERNATION.
Only the superuser may call reboot().
The precise effect of the above actions depends on the
architecture. For the i386 architecture, the additional argument
does not do anything at present (2.1.122), but the type of reboot
can be determined by kernel command-line arguments ("reboot=...")
to be either warm or cold, and either hard or through the BIOS.
Behavior inside PID namespaces
Since Linux 3.4, if reboot() is called from a PID namespace other
than the initial PID namespace with one of the cmd values listed
below, it performs a "reboot" of that namespace: the "init"
process of the PID namespace is immediately terminated, with the
effects described in pid_namespaces(7).
The values that can be supplied in cmd when calling reboot() in
this case are as follows:
LINUX_REBOOT_CMD_RESTART, LINUX_REBOOT_CMD_RESTART2
The "init" process is terminated, and wait(2) in the
parent process reports that the child was killed with a
SIGHUP signal.
LINUX_REBOOT_CMD_POWER_OFF, LINUX_REBOOT_CMD_HALT
The "init" process is terminated, and wait(2) in the
parent process reports that the child was killed with a
SIGINT signal.
For the other cmd values, reboot() returns -1 and errno is set to
EINVAL.
Возвращаемое значение (Return value)
For the values of cmd that stop or restart the system, a
successful call to reboot() does not return. For the other cmd
values, zero is returned on success. In all cases, -1 is
returned on failure, and errno is set to indicate the error.
Ошибки (Error)
EFAULT Problem with getting user-space data under
LINUX_REBOOT_CMD_RESTART2.
EINVAL Bad magic numbers or cmd.
EPERM The calling process has insufficient privilege to call
reboot(); the caller must have the CAP_SYS_BOOT inside its
user namespace.
Стандарты (Conforming to)
reboot() is Linux-specific, and should not be used in programs
intended to be portable.
Смотри также (See also)
systemctl(1), systemd(1), kexec_load(2), sync(2), bootparam(7),
capabilities(7), ctrlaltdel(8), halt(8), shutdown(8)
