поддержка синтаксиса необработанных событий perf_events (support for perf_events raw events syntax)
Имя (Name)
libpfm_perf_event_raw - support for perf_events raw events syntax
Синопсис (Synopsis)
#include <perfmon/pfmlib.h>
PMU name: perf_raw
PMU desc: Raw perf_events event syntax
Описание (Description)
The library supports a pseudo PMU model to allow raw encodings of
PMU events for the Linux perf_events kernel interface.
With this PMU, it is possible to provide the raw hexadecimal
encoding of any hardware event for any PMU models. The raw
encoding is passed as is to the kernel. All events are encoded as
PERF_TYPE_RAW. As such, perf_events generic events, such as
cycles, instructions, cannot be encoded by this PMU.
The syntax is very simple: rX. X is the hexadecimal 64-bit value
for the event. It may include event filters on some PMU models.
The hexadecimal number is passed without the 0x prefix, e.g.,
r01c4.
The library's standard perf_events attributes are supported by
this PMU model. They are separated with colons as is customary
with the library.
Модификаторы (Modifiers)
The following modifiers are supported by this PMU model:
u Measure at user level which includes privilege levels 1,
2, 3. This corresponds to PFM_PLM3. This is a boolean
modifier.
k Measure at kernel level which includes privilege level 0.
This corresponds to PFM_PLM0. This is a boolean modifier.
h Measure at the hypervisor level. This corresponds to
PFM_PLMH. This is a boolean modifier
mg Measure guest execution only. This is a boolean modifier
mh Measure host execution only. This is a boolean modifier
period Specify the the sampling period value. Value can be
expressed in decimal or hexadecimal. Value is 64-bit
wide. This option is mutually exclusive with freq. The
period is expressed in the unit of the event. There is no
default value.
freq Specify the the sampling frequency value. Value can be
expressed in decimal or hexadecimal. Value is 64-bit
wide. This options is mutually exclusive with period. The
value is expressed in Hertz. For instance, freq=100, means
that the event should be sampled 100 times per second on
average. There is no default value.
excl The associated event is the only event measured on the
PMU. This applies only to hardware events. This attribute
requires admin privileges. Default is off.
precise
Enables precise sampling mode. This option is only valid
when sampling on events. The options takes an integer
argument. It can have the following values: 1=enable
precise sampling, 2=enable precise sampling and eliminate
skid, 3=enable precise sampling, eliminate skid and bias.
Not all events necessarily support precise mode at all
levels, this is dependent on the underlying PMU.
Eliminating skid is a best effort feature. It may not work
for all samples. This option is mutually exclusive with
hw_smpl. This options implies using the hardware assist
sampling mechanism.
hw_smpl
Enables hardware assist sampling. This is a boolean
option. It is false by default. On some processors, it is
possible to have the hardware record samples in a buffer
and then notify the kernel when it is full. Such feature
may not be available for all events. Using a hardware
buffer does not necessarily eliminate skid and bias, it
usually lowers the overhead of interrupt-based sampling by
amortizing the interrupt over multiple samples. This
option is usually implicit with precise sampling events.
cpu This integer option is used with system-wide events, i.e.,
events attached to a CPU instead of a thread. The value
designate the CPU to attach the event to. It is up to the
caller of the library to use the cpu field in the library
event encoding argument to create the event. No
verification on the validity of the CPU number is made by
the library. Default value is -1 for this field.
pinned This boolean option is used with system-wide events, i.e.,
events attached to a CPU instead of a thread. If set, then
the event is marked as pinned. That means it needs to
remain on the counters at all time, i.e., it cannot be
multiplexed. There can only be as many pinned events as
there are counters, yet the library does not check for
that, the perf_event subsystem does. The default value for
this field is false, i.e., the event is not pinned.
