--ovnnb-db=database
The OVSDB database containing the OVN Northbound Database.
If the OVN_NB_DB environment variable is set, its value is
used as the default. Otherwise, the default is
unix:/usr/local/var/run/openvswitch/ovnnb_db.sock.
--ovnsb-db=database
The OVSDB database containing the OVN Southbound Database.
If the OVN_SB_DB environment variable is set, its value is
used as the default. Otherwise, the default is
unix:/usr/local/var/run/openvswitch/ovnsb_db.sock.
database in the above options must be an OVSDB active or passive
connection method, as described in ovsdb(7).
Daemon Options
--pidfile[=pidfile]
Causes a file (by default, program.pid) to be created
indicating the PID of the running process. If the pidfile
argument is not specified, or if it does not begin with /,
then it is created in /usr/local/var/run/openvswitch.
If --pidfile is not specified, no pidfile is created.
--overwrite-pidfile
By default, when --pidfile is specified and the specified
pidfile already exists and is locked by a running process,
the daemon refuses to start. Specify --overwrite-pidfile
to cause it to instead overwrite the pidfile.
When --pidfile is not specified, this option has no
effect.
--detach
Runs this program as a background process. The process
forks, and in the child it starts a new session, closes
the standard file descriptors (which has the side effect
of disabling logging to the console), and changes its
current directory to the root (unless --no-chdir is
specified). After the child completes its initialization,
the parent exits.
--monitor
Creates an additional process to monitor this program. If
it dies due to a signal that indicates a programming error
(SIGABRT, SIGALRM, SIGBUS, SIGFPE, SIGILL, SIGPIPE,
SIGSEGV, SIGXCPU, or SIGXFSZ) then the monitor process
starts a new copy of it. If the daemon dies or exits for
another reason, the monitor process exits.
This option is normally used with --detach, but it also
functions without it.
--no-chdir
By default, when --detach is specified, the daemon changes
its current working directory to the root directory after
it detaches. Otherwise, invoking the daemon from a
carelessly chosen directory would prevent the
administrator from unmounting the file system that holds
that directory.
Specifying --no-chdir suppresses this behavior, preventing
the daemon from changing its current working directory.
This may be useful for collecting core files, since it is
common behavior to write core dumps into the current
working directory and the root directory is not a good
directory to use.
This option has no effect when --detach is not specified.
--no-self-confinement
By default this daemon will try to self-confine itself to
work with files under well-known directories whitelisted
at build time. It is better to stick with this default
behavior and not to use this flag unless some other Access
Control is used to confine daemon. Note that in contrast
to other access control implementations that are typically
enforced from kernel-space (e.g. DAC or MAC), self-
confinement is imposed from the user-space daemon itself
and hence should not be considered as a full confinement
strategy, but instead should be viewed as an additional
layer of security.
--user=user:group
Causes this program to run as a different user specified
in user:group, thus dropping most of the root privileges.
Short forms user and :group are also allowed, with current
user or group assumed, respectively. Only daemons started
by the root user accepts this argument.
On Linux, daemons will be granted CAP_IPC_LOCK and
CAP_NET_BIND_SERVICES before dropping root privileges.
Daemons that interact with a datapath, such as
ovs-vswitchd, will be granted three additional
capabilities, namely CAP_NET_ADMIN, CAP_NET_BROADCAST and
CAP_NET_RAW. The capability change will apply even if the
new user is root.
On Windows, this option is not currently supported. For
security reasons, specifying this option will cause the
daemon process not to start.
Logging Options
-v[spec]
--verbose=[spec]
Sets logging levels. Without any spec, sets the log level
for every module and destination to dbg. Otherwise, spec is
a list of words separated by spaces or commas or colons, up
to one from each category below:
• A valid module name, as displayed by the vlog/list
command on ovs-appctl(8), limits the log level change
to the specified module.
• syslog, console, or file, to limit the log level
change to only to the system log, to the console, or
to a file, respectively. (If --detach is specified,
the daemon closes its standard file descriptors, so
logging to the console will have no effect.)
On Windows platform, syslog is accepted as a word and
is only useful along with the --syslog-target option
(the word has no effect otherwise).
• off, emer, err, warn, info, or dbg, to control the
log level. Messages of the given severity or higher
will be logged, and messages of lower severity will
be filtered out. off filters out all messages. See
ovs-appctl(8) for a definition of each log level.
Case is not significant within spec.
Regardless of the log levels set for file, logging to a file
will not take place unless --log-file is also specified (see
below).
For compatibility with older versions of OVS, any is
accepted as a word but has no effect.
-v
--verbose
Sets the maximum logging verbosity level, equivalent to
--verbose=dbg.
-vPATTERN:destination:pattern
--verbose=PATTERN:destination:pattern
Sets the log pattern for destination to pattern. Refer to
ovs-appctl(8) for a description of the valid syntax for
pattern.
-vFACILITY:facility
--verbose=FACILITY:facility
Sets the RFC5424 facility of the log message. facility can
be one of kern, user, mail, daemon, auth, syslog, lpr, news,
uucp, clock, ftp, ntp, audit, alert, clock2, local0, local1,
local2, local3, local4, local5, local6 or local7. If this
option is not specified, daemon is used as the default for
the local system syslog and local0 is used while sending a
message to the target provided via the --syslog-target
option.
--log-file[=file]
Enables logging to a file. If file is specified, then it is
used as the exact name for the log file. The default log
file name used if file is omitted is
/usr/local/var/log/openvswitch/program.log.
--syslog-target=host:port
Send syslog messages to UDP port on host, in addition to the
system syslog. The host must be a numerical IP address, not
a hostname.
--syslog-method=method
Specify method as how syslog messages should be sent to
syslog daemon. The following forms are supported:
• libc, to use the libc syslog() function. Downside of
using this options is that libc adds fixed prefix to
every message before it is actually sent to the
syslog daemon over /dev/log UNIX domain socket.
• unix:file, to use a UNIX domain socket directly. It
is possible to specify arbitrary message format with
this option. However, rsyslogd 8.9 and older versions
use hard coded parser function anyway that limits
UNIX domain socket use. If you want to use arbitrary
message format with older rsyslogd versions, then use
UDP socket to localhost IP address instead.
• udp:ip:port, to use a UDP socket. With this method it
is possible to use arbitrary message format also with
older rsyslogd. When sending syslog messages over UDP
socket extra precaution needs to be taken into
account, for example, syslog daemon needs to be
configured to listen on the specified UDP port,
accidental iptables rules could be interfering with
local syslog traffic and there are some security
considerations that apply to UDP sockets, but do not
apply to UNIX domain sockets.
• null, to discard all messages logged to syslog.
The default is taken from the OVS_SYSLOG_METHOD environment
variable; if it is unset, the default is libc.
PKI Options
PKI configuration is required in order to use SSL for the
connections to the Northbound and Southbound databases.
-p privkey.pem
--private-key=privkey.pem
Specifies a PEM file containing the private key used
as identity for outgoing SSL connections.
-c cert.pem
--certificate=cert.pem
Specifies a PEM file containing a certificate that
certifies the private key specified on -p or
--private-key to be trustworthy. The certificate must
be signed by the certificate authority (CA) that the
peer in SSL connections will use to verify it.
-C cacert.pem
--ca-cert=cacert.pem
Specifies a PEM file containing the CA certificate
for verifying certificates presented to this program
by SSL peers. (This may be the same certificate that
SSL peers use to verify the certificate specified on
-c or --certificate, or it may be a different one,
depending on the PKI design in use.)
-C none
--ca-cert=none
Disables verification of certificates presented by
SSL peers. This introduces a security risk, because
it means that certificates cannot be verified to be
those of known trusted hosts.
Other Options
--unixctl=socket
Sets the name of the control socket on which program
listens for runtime management commands (see RUNTIME
MANAGEMENT COMMANDS, below). If socket does not begin with
/, it is interpreted as relative to
/usr/local/var/run/openvswitch. If --unixctl is not used
at all, the default socket is
/usr/local/var/run/openvswitch/program.pid.ctl, where pid
is program's process ID.
On Windows a local named pipe is used to listen for
runtime management commands. A file is created in the
absolute path as pointed by socket or if --unixctl is not
used at all, a file is created as program in the
configured OVS_RUNDIR directory. The file exists just to
mimic the behavior of a Unix domain socket.
Specifying none for socket disables the control socket
feature.
-h
--help
Prints a brief help message to the console.
-V
--version
Prints version information to the console.
