---

   can_change_color.3x    ( 3 )

---

Функции (Functions)

start_color The start_color routine requires no arguments. It must be called if the programmer wants to use colors, and before any other color manipulation routine is called. It is good practice to call this routine right after initscr. start_color does this:

• It initializes two global variables, COLORS and COLOR_PAIRS (respectively defining the maximum number of colors and color-pairs the terminal can support).

• It initializes the special color pair 0 to the default foreground and background colors. No other color pairs are initialized.

• It restores the colors on the terminal to the values they had when the terminal was just turned on.

• If the terminal supports the initc (initialize_color) capability, start_color initializes its internal table representing the red, green, and blue components of the color palette.

The components depend on whether the terminal uses CGA (aka 'ANSI') or HLS (i.e., the hls (hue_lightness_saturation) capability is set). The table is initialized first for eight basic colors (black, red, green, yellow, blue, magenta, cyan, and white), using weights that depend upon the CGA/HLS choice. For 'ANSI' colors the weights are 680 or 0 depending on whether the corresponding red, green, or blue component is used or not. That permits using 1000 to represent bold/bright colors. After the initial eight colors (if the terminal supports more than eight colors) the components are initialized using the same pattern, but with weights of 1000. SVr4 uses a similar scheme, but uses 1000 for the components of the initial eight colors.

start_color does not attempt to set the terminal's color palette to match its built-in table. An application may use init_color to alter the internal table along with the terminal's color.

These limits apply to color values and color pairs. Values outside these limits are not legal, and may result in a runtime error:

• COLORS corresponds to the terminal database's max_colors capability, (see terminfo(5)).

• color values are expected to be in the range 0 to COLORS-1, inclusive (including 0 and COLORS-1).

• a special color value -1 is used in certain extended functions to denote the default color (see use_default_colors(3X)).

• COLOR_PAIRS corresponds to the terminal database's max_pairs capability, (see terminfo(5)).

• legal color pair values are in the range 1 to COLOR_PAIRS-1, inclusive.

• color pair 0 is special; it denotes 'no color'.

Color pair 0 is assumed to be white on black, but is actually whatever the terminal implements before color is initialized. It cannot be modified by the application.

has_colors The has_colors routine requires no arguments. It returns TRUE if the terminal can manipulate colors; otherwise, it returns FALSE. This routine facilitates writing terminal-independent programs. For example, a programmer can use it to decide whether to use color or some other video attribute.

can_change_color The can_change_color routine requires no arguments. It returns TRUE if the terminal supports colors and can change their definitions; other, it returns FALSE. This routine facilitates writing terminal-independent programs.

init_pair The init_pair routine changes the definition of a color-pair. It takes three arguments: the number of the color-pair to be changed, the foreground color number, and the background color number. For portable applications:

• The first argument must be a legal color pair value. If default colors are used (see use_default_colors(3X)) the upper limit is adjusted to allow for extra pairs which use a default color in foreground and/or background.

• The second and third arguments must be legal color values.

If the color-pair was previously initialized, the screen is refreshed and all occurrences of that color-pair are changed to the new definition.

As an extension, ncurses allows you to set color pair 0 via the assume_default_colors(3X) routine, or to specify the use of default colors (color number -1) if you first invoke the use_default_colors(3X) routine.

init_extended_pair Because init_pair uses signed shorts for its parameters, that limits color-pairs and color-values to 32767 on modern hardware. The extension init_extended_pair uses ints for the color-pair and color-value, allowing a larger number of colors to be supported.

init_color The init_color routine changes the definition of a color. It takes four arguments: the number of the color to be changed followed by three RGB values (for the amounts of red, green, and blue components).

• The first argument must be a legal color value; default colors are not allowed here. (See the section Colors for the default color index.)

• Each of the last three arguments must be a value in the range 0 through 1000.

When init_color is used, all occurrences of that color on the screen immediately change to the new definition.

init_extended_color Because init_color uses signed shorts for its parameters, that limits color-values and their red, green, and blue components to 32767 on modern hardware. The extension init_extended_color uses ints for the color value and for setting the red, green, and blue components, allowing a larger number of colors to be supported.

color_content The color_content routine gives programmers a way to find the intensity of the red, green, and blue (RGB) components in a color. It requires four arguments: the color number, and three addresses of shorts for storing the information about the amounts of red, green, and blue components in the given color.

• The first argument must be a legal color value, i.e., 0 through COLORS-1, inclusive.

• The values that are stored at the addresses pointed to by the last three arguments are in the range 0 (no component) through 1000 (maximum amount of component), inclusive.

extended_color_content Because color_content uses signed shorts for its parameters, that limits color-values and their red, green, and blue components to 32767 on modern hardware. The extension extended_color_content uses ints for the color value and for returning the red, green, and blue components, allowing a larger number of colors to be supported.

pair_content The pair_content routine allows programmers to find out what colors a given color-pair consists of. It requires three arguments: the color-pair number, and two addresses of shorts for storing the foreground and the background color numbers.

• The first argument must be a legal color value, i.e., in the range 1 through COLOR_PAIRS-1, inclusive.

• The values that are stored at the addresses pointed to by the second and third arguments are in the range 0 through COLORS, inclusive.

extended_pair_content Because pair_content uses signed shorts for its parameters, that limits color-pair and color-values to 32767 on modern hardware. The extension extended_pair_content uses ints for the color pair and for returning the foreground and background colors, allowing a larger number of colors to be supported.

reset_color_pairs The extension reset_color_pairs tells ncurses to discard all of the color-pair information which was set with init_pair. It also touches the current- and standard-screens, allowing an application to switch color palettes rapidly.

PAIR_NUMBER PAIR_NUMBER(attrs) extracts the color value from its attrs parameter and returns it as a color pair number.

COLOR_PAIR Its inverse COLOR_PAIR(n) converts a color pair number to an attribute. Attributes can hold color pairs in the range 0 to 255. If you need a color pair larger than that, you must use functions such as attr_set (which pass the color pair as a separate parameter) rather than the legacy functions such as attrset.