схема базы данных Open_vSwitch (Open_vSwitch database schema)
Port TABLE
A port within a Bridge.
Most commonly, a port has exactly one ``interface,'' pointed to
by its interfaces column. Such a port logically corresponds to a
port on a physical Ethernet switch. A port with more than one
interface is a ``bonded port'' (see Bonding Configuration).
Some properties that one might think as belonging to a port are
actually part of the port's Interface members.
Summary:
name immutable string (must be unique
within table)
interfaces set of 1 or more Interfaces
VLAN Configuration:
vlan_mode optional string, one of access,
dot1q-tunnel, native-tagged,
native-untagged, or trunk
tag optional integer, in range 0 to
4,095
trunks set of up to 4,096 integers, in
range 0 to 4,095
cvlans set of up to 4,096 integers, in
range 0 to 4,095
other_config : qinq-ethtype
optional string, either 802.1ad or
802.1q
other_config : priority-tags
optional string, one of always,
if-nonzero, or never
Bonding Configuration:
bond_mode optional string, one of
active-backup, balance-slb, or
balance-tcp
other_config : bond-hash-basis
optional string, containing an
integer
other_config : lb-output-action
optional string, either true or
false
other_config : bond-primary
optional string
Link Failure Detection:
other_config : bond-detect-mode
optional string, either carrier or
miimon
other_config : bond-miimon-interval
optional string, containing an
integer
bond_updelay integer
bond_downdelay integer
LACP Configuration:
lacp optional string, one of active,
off, or passive
other_config : lacp-system-id
optional string
other_config : lacp-system-priority
optional string, containing an
integer, in range 1 to 65,535
other_config : lacp-time optional string, either fast or
slow
other_config : lacp-fallback-ab
optional string, either true or
false
Rebalancing Configuration:
other_config : bond-rebalance-interval
optional string, containing an
integer, in range 0 to
2,147,483,647
bond_fake_iface boolean
Spanning Tree Protocol:
STP Configuration:
other_config : stp-enable
optional string, either true or
false
other_config : stp-port-num
optional string, containing an
integer, in range 1 to 255
other_config : stp-port-priority
optional string, containing an
integer, in range 0 to 255
other_config : stp-path-cost
optional string, containing an
integer, in range 0 to 65,535
STP Status:
status : stp_port_id optional string
status : stp_state optional string, one of blocking,
disabled, forwarding, learning, or
listening
status : stp_sec_in_state
optional string, containing an
integer, at least 0
status : stp_role optional string, one of alternate,
designated, or root
Rapid Spanning Tree Protocol:
RSTP Configuration:
other_config : rstp-enable
optional string, either true or
false
other_config : rstp-port-priority
optional string, containing an
integer, in range 0 to 240
other_config : rstp-port-num
optional string, containing an
integer, in range 1 to 4,095
other_config : rstp-port-path-cost
optional string, containing an
integer
other_config : rstp-port-admin-edge
optional string, either true or
false
other_config : rstp-port-auto-edge
optional string, either true or
false
other_config : rstp-port-mcheck
optional string, either true or
false
RSTP Status:
rstp_status : rstp_port_id
optional string
rstp_status : rstp_port_role
optional string, one of Alternate,
Backup, Designated, Disabled, or
Root
rstp_status : rstp_port_state
optional string, one of Disabled,
Discarding, Forwarding, or Learning
rstp_status : rstp_designated_bridge_id
optional string
rstp_status : rstp_designated_port_id
optional string
rstp_status : rstp_designated_path_cost
optional string, containing an
integer
RSTP Statistics:
rstp_statistics : rstp_tx_count
optional integer
rstp_statistics : rstp_rx_count
optional integer
rstp_statistics : rstp_error_count
optional integer
rstp_statistics : rstp_uptime
optional integer
Multicast Snooping:
other_config : mcast-snooping-flood
optional string, either true or
false
other_config : mcast-snooping-flood-reports
optional string, either true or
false
Other Features:
qos optional QoS
mac optional string
fake_bridge boolean
protected boolean
external_ids : fake-bridge-id-*
optional string
other_config : transient optional string, either true or
false
bond_active_slave optional string
Port Statistics:
Statistics: STP transmit and receive counters:
statistics : stp_tx_count
optional integer
statistics : stp_rx_count
optional integer
statistics : stp_error_count
optional integer
Common Columns:
other_config map of string-string pairs
external_ids map of string-string pairs
Details:
name: immutable string (must be unique within table)
Port name. For a non-bonded port, this should be the same
as its interface's name. Port names must otherwise be
unique among the names of ports, interfaces, and bridges
on a host. Because port and interfaces names are usually
the same, the restrictions on the name column in the
Interface table, particularly on length, also apply to
port names. Refer to the documentation for Interface names
for details.
interfaces: set of 1 or more Interfaces
The port's interfaces. If there is more than one, this is
a bonded Port.
VLAN Configuration:
In short, a VLAN (short for ``virtual LAN'') is a way to
partition a single switch into multiple switches. VLANs can be
confusing, so for an introduction, please refer to the question
``What's a VLAN?'' in the Open vSwitch FAQ.
A VLAN is sometimes encoded into a packet using a 802.1Q or
802.1ad VLAN header, but every packet is part of some VLAN
whether or not it is encoded in the packet. (A packet that
appears to have no VLAN is part of VLAN 0, by default.) As a
result, it's useful to think of a VLAN as a metadata property of
a packet, separate from how the VLAN is encoded. For a given
port, this column determines how the encoding of a packet that
ingresses or egresses the port maps to the packet's VLAN. When a
packet enters the switch, its VLAN is determined based on its
setting in this column and its VLAN headers, if any, and then,
conceptually, the VLAN headers are then stripped off. Conversely,
when a packet exits the switch, its VLAN and the settings in this
column determine what VLAN headers, if any, are pushed onto the
packet before it egresses the port.
The VLAN configuration in this column affects Open vSwitch only
when it is doing ``normal switching.'' It does not affect flows
set up by an OpenFlow controller, outside of the OpenFlow
``normal action.''
Bridge ports support the following types of VLAN configuration:
trunk A trunk port carries packets on one or more
specified VLANs specified in the trunks column
(often, on every VLAN). A packet that ingresses on
a trunk port is in the VLAN specified in its 802.1Q
header, or VLAN 0 if the packet has no 802.1Q
header. A packet that egresses through a trunk port
will have an 802.1Q header if it has a nonzero VLAN
ID.
Any packet that ingresses on a trunk port tagged
with a VLAN that the port does not trunk is
dropped.
access An access port carries packets on exactly one VLAN
specified in the tag column. Packets egressing on
an access port have no 802.1Q header.
Any packet with an 802.1Q header with a nonzero
VLAN ID that ingresses on an access port is
dropped, regardless of whether the VLAN ID in the
header is the access port's VLAN ID.
native-tagged
A native-tagged port resembles a trunk port, with
the exception that a packet without an 802.1Q
header that ingresses on a native-tagged port is in
the ``native VLAN'' (specified in the tag column).
native-untagged
A native-untagged port resembles a native-tagged
port, with the exception that a packet that
egresses on a native-untagged port in the native
VLAN will not have an 802.1Q header.
dot1q-tunnel
A dot1q-tunnel port is somewhat like an access
port. Like an access port, it carries packets on
the single VLAN specified in the tag column and
this VLAN, called the service VLAN, does not appear
in an 802.1Q header for packets that ingress or
egress on the port. The main difference lies in the
behavior when packets that include a 802.1Q header
ingress on the port. Whereas an access port drops
such packets, a dot1q-tunnel port treats these as
double-tagged with the outer service VLAN tag and
the inner customer VLAN taken from the 802.1Q
header. Correspondingly, to egress on the port, a
packet outer VLAN (or only VLAN) must be tag, which
is removed before egress, which exposes the inner
(customer) VLAN if one is present.
If cvlans is set, only allows packets in the
specified customer VLANs.
A packet will only egress through bridge ports that carry the
VLAN of the packet, as described by the rules above.
vlan_mode: optional string, one of access, dot1q-tunnel,
native-tagged, native-untagged, or trunk
The VLAN mode of the port, as described above. When this
column is empty, a default mode is selected as follows:
• If tag contains a value, the port is an access
port. The trunks column should be empty.
• Otherwise, the port is a trunk port. The trunks
column value is honored if it is present.
tag: optional integer, in range 0 to 4,095
For an access port, the port's implicitly tagged VLAN. For
a native-tagged or native-untagged port, the port's native
VLAN. Must be empty if this is a trunk port.
trunks: set of up to 4,096 integers, in range 0 to 4,095
For a trunk, native-tagged, or native-untagged port, the
802.1Q VLAN or VLANs that this port trunks; if it is
empty, then the port trunks all VLANs. Must be empty if
this is an access port.
A native-tagged or native-untagged port always trunks its
native VLAN, regardless of whether trunks includes that
VLAN.
cvlans: set of up to 4,096 integers, in range 0 to 4,095
For a dot1q-tunnel port, the customer VLANs that this port
includes. If this is empty, the port includes all customer
VLANs.
For other kinds of ports, this setting is ignored.
other_config : qinq-ethtype: optional string, either 802.1ad or
802.1q
For a dot1q-tunnel port, this is the TPID for the service
tag, that is, for the 802.1Q header that contains the
service VLAN ID. Because packets that actually ingress and
egress a dot1q-tunnel port do not include an 802.1Q header
for the service VLAN, this does not affect packets on the
dot1q-tunnel port itself. Rather, it determines the
service VLAN for a packet that ingresses on a dot1q-tunnel
port and egresses on a trunk port.
The value 802.1ad specifies TPID 0x88a8, which is also the
default if the setting is omitted. The value 802.1q
specifies TPID 0x8100.
For other kinds of ports, this setting is ignored.
other_config : priority-tags: optional string, one of always,
if-nonzero, or never
An 802.1Q header contains two important pieces of
information: a VLAN ID and a priority. A frame with a zero
VLAN ID, called a ``priority-tagged'' frame, is supposed
to be treated the same way as a frame without an 802.1Q
header at all (except for the priority).
However, some network elements ignore any frame that has
802.1Q header at all, even when the VLAN ID is zero.
Therefore, by default Open vSwitch does not output
priority-tagged frames, instead omitting the 802.1Q header
entirely if the VLAN ID is zero. Set this key to
if-nonzero to enable priority-tagged frames on a port.
For if-nonzero Open vSwitch omits the 802.1Q header on
output if both the VLAN ID and priority would be zero. Set
to always to retain the 802.1Q header in such frames as
well.
All frames output to native-tagged ports have a nonzero
VLAN ID, so this setting is not meaningful on native-
tagged ports.
Bonding Configuration:
A port that has more than one interface is a ``bonded port.''
Bonding allows for load balancing and fail-over.
The following types of bonding will work with any kind of
upstream switch. On the upstream switch, do not configure the
interfaces as a bond:
balance-slb
Balances flows among members based on source MAC
address and output VLAN, with periodic rebalancing
as traffic patterns change.
active-backup
Assigns all flows to one member, failing over to a
backup member when the active member is disabled.
This is the only bonding mode in which interfaces
may be plugged into different upstream switches.
The following modes require the upstream switch to support
802.3ad with successful LACP negotiation. If LACP negotiation
fails and other-config:lacp-fallback-ab is true, then
active-backup mode is used:
balance-tcp
Balances flows among members based on L3 and L4
protocol information such as IP addresses and
TCP/UDP ports.
These columns apply only to bonded ports. Their values are
otherwise ignored.
bond_mode: optional string, one of active-backup, balance-slb, or
balance-tcp
The type of bonding used for a bonded port. Defaults to
active-backup if unset.
other_config : bond-hash-basis: optional string, containing an
integer
An integer hashed along with flows when choosing output
members in load balanced bonds. When changed, all flows
will be assigned different hash values possibly causing
member selection decisions to change. Does not affect
bonding modes which do not employ load balancing such as
active-backup.
other_config : lb-output-action: optional string, either true or
false
Enable/disable usage of optimized lb_output action for
balancing flows among output members in load balanced
bonds in balance-tcp. When enabled, it uses optimized path
for balance-tcp mode by using rss hash and avoids
recirculation. This knob does not affect other balancing
modes.
other_config : bond-primary: optional string
If a slave interface with this name exists in the bond and
is up, it will be made active. Relevant only when
other_config:bond_mode is active-backup or if balance-tcp
falls back to active-backup (e.g., LACP negotiation fails
and other_config:lacp-fallback-ab is true).
Link Failure Detection:
An important part of link bonding is detecting that links are
down so that they may be disabled. These settings determine how
Open vSwitch detects link failure.
other_config : bond-detect-mode: optional string, either carrier
or miimon
The means used to detect link failures. Defaults to
carrier which uses each interface's carrier to detect
failures. When set to miimon, will check for failures by
polling each interface's MII.
other_config : bond-miimon-interval: optional string, containing
an integer
The interval, in milliseconds, between successive attempts
to poll each interface's MII. Relevant only when
other_config:bond-detect-mode is miimon.
bond_updelay: integer
The number of milliseconds for which the link must stay up
on an interface before the interface is considered to be
up. Specify 0 to enable the interface immediately.
This setting is honored only when at least one bonded
interface is already enabled. When no interfaces are
enabled, then the first bond interface to come up is
enabled immediately.
bond_downdelay: integer
The number of milliseconds for which the link must stay
down on an interface before the interface is considered to
be down. Specify 0 to disable the interface immediately.
LACP Configuration:
LACP, the Link Aggregation Control Protocol, is an IEEE standard
that allows switches to automatically detect that they are
connected by multiple links and aggregate across those links.
These settings control LACP behavior.
lacp: optional string, one of active, off, or passive
Configures LACP on this port. LACP allows directly
connected switches to negotiate which links may be bonded.
LACP may be enabled on non-bonded ports for the benefit of
any switches they may be connected to. active ports are
allowed to initiate LACP negotiations. passive ports are
allowed to participate in LACP negotiations initiated by a
remote switch, but not allowed to initiate such
negotiations themselves. If LACP is enabled on a port
whose partner switch does not support LACP, the bond will
be disabled, unless other-config:lacp-fallback-ab is set
to true. Defaults to off if unset.
other_config : lacp-system-id: optional string
The LACP system ID of this Port. The system ID of a LACP
bond is used to identify itself to its partners. Must be a
nonzero MAC address. Defaults to the bridge Ethernet
address if unset.
other_config : lacp-system-priority: optional string, containing
an integer, in range 1 to 65,535
The LACP system priority of this Port. In LACP
negotiations, link status decisions are made by the system
with the numerically lower priority.
other_config : lacp-time: optional string, either fast or slow
The LACP timing which should be used on this Port. By
default slow is used. When configured to be fast LACP
heartbeats are requested at a rate of once per second
causing connectivity problems to be detected more quickly.
In slow mode, heartbeats are requested at a rate of once
every 30 seconds.
other_config : lacp-fallback-ab: optional string, either true or
false
Determines the behavior of openvswitch bond in LACP mode.
If the partner switch does not support LACP, setting this
option to true allows openvswitch to fallback to active-
backup. If the option is set to false, the bond will be
disabled. In both the cases, once the partner switch is
configured to LACP mode, the bond will use LACP.
Rebalancing Configuration:
These settings control behavior when a bond is in balance-slb or
balance-tcp mode.
other_config : bond-rebalance-interval: optional string,
containing an integer, in range 0 to 2,147,483,647
For a load balanced bonded port, the number of
milliseconds between successive attempts to rebalance the
bond, that is, to move flows from one interface on the
bond to another in an attempt to keep usage of each
interface roughly equal. If zero, load balancing is
disabled on the bond (link failure still cause flows to
move). If less than 1000ms, the rebalance interval will be
1000ms.
bond_fake_iface: boolean
For a bonded port, whether to create a fake internal
interface with the name of the port. Use only for
compatibility with legacy software that requires this.
Spanning Tree Protocol:
The configuration here is only meaningful, and the status is only
populated, when 802.1D-1998 Spanning Tree Protocol is enabled on
the port's Bridge with its stp_enable column.
STP Configuration:
other_config : stp-enable: optional string, either true or false
When STP is enabled on a bridge, it is enabled by default
on all of the bridge's ports except bond, internal, and
mirror ports (which do not work with STP). If this
column's value is false, STP is disabled on the port.
other_config : stp-port-num: optional string, containing an
integer, in range 1 to 255
The port number used for the lower 8 bits of the port-id.
By default, the numbers will be assigned automatically. If
any port's number is manually configured on a bridge, then
they must all be.
other_config : stp-port-priority: optional string, containing an
integer, in range 0 to 255
The port's relative priority value for determining the
root port (the upper 8 bits of the port-id). A port with a
lower port-id will be chosen as the root port. By default,
the priority is 0x80.
other_config : stp-path-cost: optional string, containing an
integer, in range 0 to 65,535
Spanning tree path cost for the port. A lower number
indicates a faster link. By default, the cost is based on
the maximum speed of the link.
STP Status:
status : stp_port_id: optional string
The port ID used in spanning tree advertisements for this
port, as 4 hex digits. Configuring the port ID is
described in the stp-port-num and stp-port-priority keys
of the other_config section earlier.
status : stp_state: optional string, one of blocking, disabled,
forwarding, learning, or listening
STP state of the port.
status : stp_sec_in_state: optional string, containing an
integer, at least 0
The amount of time this port has been in the current STP
state, in seconds.
status : stp_role: optional string, one of alternate, designated,
or root
STP role of the port.
Rapid Spanning Tree Protocol:
The configuration here is only meaningful, and the status and
statistics are only populated, when 802.1D-1998 Spanning Tree
Protocol is enabled on the port's Bridge with its stp_enable
column.
RSTP Configuration:
other_config : rstp-enable: optional string, either true or false
When RSTP is enabled on a bridge, it is enabled by default
on all of the bridge's ports except bond, internal, and
mirror ports (which do not work with RSTP). If this
column's value is false, RSTP is disabled on the port.
other_config : rstp-port-priority: optional string, containing an
integer, in range 0 to 240
The port's relative priority value for determining the
root port, in multiples of 16. By default, the port
priority is 0x80 (128). Any value in the lower 4 bits is
rounded off. The significant upper 4 bits become the upper
4 bits of the port-id. A port with the lowest port-id is
elected as the root.
other_config : rstp-port-num: optional string, containing an
integer, in range 1 to 4,095
The local RSTP port number, used as the lower 12 bits of
the port-id. By default the port numbers are assigned
automatically, and typically may not correspond to the
OpenFlow port numbers. A port with the lowest port-id is
elected as the root.
other_config : rstp-port-path-cost: optional string, containing
an integer
The port path cost. The Port's contribution, when it is
the Root Port, to the Root Path Cost for the Bridge. By
default the cost is automatically calculated from the
port's speed.
other_config : rstp-port-admin-edge: optional string, either true
or false
The admin edge port parameter for the Port. Default is
false.
other_config : rstp-port-auto-edge: optional string, either true
or false
The auto edge port parameter for the Port. Default is
true.
other_config : rstp-port-mcheck: optional string, either true or
false
The mcheck port parameter for the Port. Default is false.
May be set to force the Port Protocol Migration state
machine to transmit RST BPDUs for a MigrateTime period, to
test whether all STP Bridges on the attached LAN have been
removed and the Port can continue to transmit RSTP BPDUs.
Setting mcheck has no effect if the Bridge is operating in
STP Compatibility mode.
Changing the value from true to false has no effect, but
needs to be done if this behavior is to be triggered again
by subsequently changing the value from false to true.
RSTP Status:
rstp_status : rstp_port_id: optional string
The port ID used in spanning tree advertisements for this
port, as 4 hex digits. Configuring the port ID is
described in the rstp-port-num and rstp-port-priority keys
of the other_config section earlier.
rstp_status : rstp_port_role: optional string, one of Alternate,
Backup, Designated, Disabled, or Root
RSTP role of the port.
rstp_status : rstp_port_state: optional string, one of Disabled,
Discarding, Forwarding, or Learning
RSTP state of the port.
rstp_status : rstp_designated_bridge_id: optional string
The port's RSTP designated bridge ID, in the same form as
rstp_status:rstp_bridge_id in the Bridge table.
rstp_status : rstp_designated_port_id: optional string
The port's RSTP designated port ID, as 4 hex digits.
rstp_status : rstp_designated_path_cost: optional string,
containing an integer
The port's RSTP designated path cost. Lower is better.
RSTP Statistics:
rstp_statistics : rstp_tx_count: optional integer
Number of RSTP BPDUs transmitted through this port.
rstp_statistics : rstp_rx_count: optional integer
Number of valid RSTP BPDUs received by this port.
rstp_statistics : rstp_error_count: optional integer
Number of invalid RSTP BPDUs received by this port.
rstp_statistics : rstp_uptime: optional integer
The duration covered by the other RSTP statistics, in
seconds.
Multicast Snooping:
other_config : mcast-snooping-flood: optional string, either true
or false
If set to true, multicast packets (except Reports) are
unconditionally forwarded to the specific port.
other_config : mcast-snooping-flood-reports: optional string,
either true or false
If set to true, multicast Reports are unconditionally
forwarded to the specific port.
Other Features:
qos: optional QoS
Quality of Service configuration for this port.
mac: optional string
The MAC address to use for this port for the purpose of
choosing the bridge's MAC address. This column does not
necessarily reflect the port's actual MAC address, nor
will setting it change the port's actual MAC address.
fake_bridge: boolean
Does this port represent a sub-bridge for its tagged VLAN
within the Bridge? See ovs-vsctl(8) for more information.
protected: boolean
The protected ports feature allows certain ports to be
designated as protected. Traffic between protected ports
is blocked. Protected ports can send traffic to
unprotected ports. Unprotected ports can send traffic to
any port. Default is false.
external_ids : fake-bridge-id-*: optional string
External IDs for a fake bridge (see the fake_bridge
column) are defined by prefixing a Bridge external_ids key
with fake-bridge-, e.g. fake-bridge-xs-network-uuids.
other_config : transient: optional string, either true or false
If set to true, the port will be removed when ovs-ctl
start --delete-transient-ports is used.
bond_active_slave: optional string
For a bonded port, record the MAC address of the current
active member.
Port Statistics:
Key-value pairs that report port statistics. The update period is
controlled by other_config:stats-update-interval in the
Open_vSwitch table.
Statistics: STP transmit and receive counters:
statistics : stp_tx_count: optional integer
Number of STP BPDUs sent on this port by the spanning tree
library.
statistics : stp_rx_count: optional integer
Number of STP BPDUs received on this port and accepted by
the spanning tree library.
statistics : stp_error_count: optional integer
Number of bad STP BPDUs received on this port. Bad BPDUs
include runt packets and those with an unexpected protocol
ID.
Common Columns:
The overall purpose of these columns is described under Common
Columns at the beginning of this document.
other_config: map of string-string pairs
external_ids: map of string-string pairs
