конфигурация среды выполнения (Execution environment configuration)
ENVIRONMENT VARIABLES IN SPAWNED PROCESSES
Processes started by the service manager are executed with an
environment variable block assembled from multiple sources.
Processes started by the system service manager generally do not
inherit environment variables set for the service manager itself
(but this may be altered via PassEnvironment=), but processes
started by the user service manager instances generally do
inherit all environment variables set for the service manager
itself.
For each invoked process the list of environment variables set is
compiled from the following sources:
• Variables globally configured for the service manager, using
the DefaultEnvironment= setting in systemd-system.conf(5),
the kernel command line option systemd.setenv= understood by
systemd(1), or via systemctl(1) set-environment verb.
• Variables defined by the service manager itself (see the list
below).
• Variables set in the service manager's own environment
variable block (subject to PassEnvironment= for the system
service manager).
• Variables set via Environment= in the unit file.
• Variables read from files specified via EnvironmentFile= in
the unit file.
• Variables set by any PAM modules in case PAMName= is in
effect, cf. pam_env(8).
If the same environment variable is set by multiple of these
sources, the later source — according to the order of the list
above — wins. Note that as the final step all variables listed in
UnsetEnvironment= are removed from the compiled environment
variable list, immediately before it is passed to the executed
process.
The general philosophy is to expose a small curated list of
environment variables to processes. Services started by the
system manager (PID 1) will be started, without additional
service-specific configuration, with just a few environment
variables. The user manager inherits environment variables as any
other system service, but in addition may receive additional
environment variables from PAM, and, typically, additional
imported variables when the user starts a graphical session. It
is recommended to keep the environment blocks in both the system
and user managers managers lean. Importing all variables
inherited by the graphical session or by one of the user shells
is strongly discouraged.
Hint: systemd-run -P env and systemd-run --user -P env print the
effective system and user service environment blocks.
Environment Variables Set or Propagated by the Service Manager
The following environment variables are propagated by the service
manager or generated internally for each invoked process:
$PATH
Colon-separated list of directories to use when launching
executables. systemd uses a fixed value of
"/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin" in the
system manager. When compiled for systems with "unmerged
/usr/" (/bin is not a symlink to /usr/bin), ":/sbin:/bin" is
appended. In case of the user manager, a different path may
be configured by the distribution. It is recommended to not
rely on the order of entries, and have only one program with
a given name in $PATH.
$LANG
Locale. Can be set in locale.conf(5) or on the kernel command
line (see systemd(1) and kernel-command-line(7)).
$USER, $LOGNAME, $HOME, $SHELL
User name (twice), home directory, and the login shell. The
variables are set for the units that have User= set, which
includes user systemd instances. See passwd(5).
$INVOCATION_ID
Contains a randomized, unique 128bit ID identifying each
runtime cycle of the unit, formatted as 32 character
hexadecimal string. A new ID is assigned each time the unit
changes from an inactive state into an activating or active
state, and may be used to identify this specific runtime
cycle, in particular in data stored offline, such as the
journal. The same ID is passed to all processes run as part
of the unit.
$XDG_RUNTIME_DIR
The directory to use for runtime objects (such as IPC
objects) and volatile state. Set for all services run by the
user systemd instance, as well as any system services that
use PAMName= with a PAM stack that includes pam_systemd. See
below and pam_systemd(8) for more information.
$RUNTIME_DIRECTORY, $STATE_DIRECTORY, $CACHE_DIRECTORY,
$LOGS_DIRECTORY, $CONFIGURATION_DIRECTORY
Absolute paths to the directories defined with
RuntimeDirectory=, StateDirectory=, CacheDirectory=,
LogsDirectory=, and ConfigurationDirectory= when those
settings are used.
$CREDENTIALS_DIRECTORY
An absolute path to the per-unit directory with credentials
configured via LoadCredential=/SetCredential=. The directory
is marked read-only and is placed in unswappable memory (if
supported and permitted), and is only accessible to the UID
associated with the unit via User= or DynamicUser= (and the
superuser).
$MAINPID
The PID of the unit's main process if it is known. This is
only set for control processes as invoked by ExecReload= and
similar.
$MANAGERPID
The PID of the user systemd instance, set for processes
spawned by it.
$LISTEN_FDS, $LISTEN_PID, $LISTEN_FDNAMES
Information about file descriptors passed to a service for
socket activation. See sd_listen_fds(3).
$NOTIFY_SOCKET
The socket sd_notify() talks to. See sd_notify(3).
$WATCHDOG_PID, $WATCHDOG_USEC
Information about watchdog keep-alive notifications. See
sd_watchdog_enabled(3).
$SYSTEMD_EXEC_PID
The PID of the unit process (e.g. process invoked by
ExecStart=). The child process can use this information to
determine whether the process is directly invoked by the
service manager or indirectly as a child of another process
by comparing this value with the current PID (as similar to
the scheme used in sd_listen_fds(3) with $LISTEN_PID and
$LISTEN_FDS).
$TERM
Terminal type, set only for units connected to a terminal
(StandardInput=tty, StandardOutput=tty, or
StandardError=tty). See termcap(5).
$LOG_NAMESPACE
Contains the name of the selected logging namespace when the
LogNamespace= service setting is used.
$JOURNAL_STREAM
If the standard output or standard error output of the
executed processes are connected to the journal (for example,
by setting StandardError=journal) $JOURNAL_STREAM contains
the device and inode numbers of the connection file
descriptor, formatted in decimal, separated by a colon (":").
This permits invoked processes to safely detect whether their
standard output or standard error output are connected to the
journal. The device and inode numbers of the file descriptors
should be compared with the values set in the environment
variable to determine whether the process output is still
connected to the journal. Note that it is generally not
sufficient to only check whether $JOURNAL_STREAM is set at
all as services might invoke external processes replacing
their standard output or standard error output, without
unsetting the environment variable.
If both standard output and standard error of the executed
processes are connected to the journal via a stream socket,
this environment variable will contain information about the
standard error stream, as that's usually the preferred
destination for log data. (Note that typically the same
stream is used for both standard output and standard error,
hence very likely the environment variable contains device
and inode information matching both stream file descriptors.)
This environment variable is primarily useful to allow
services to optionally upgrade their used log protocol to the
native journal protocol (using sd_journal_print(3) and other
functions) if their standard output or standard error output
is connected to the journal anyway, thus enabling delivery of
structured metadata along with logged messages.
$SERVICE_RESULT
Only defined for the service unit type, this environment
variable is passed to all ExecStop= and ExecStopPost=
processes, and encodes the service "result". Currently, the
following values are defined:
Table 4. Defined $SERVICE_RESULT values
┌──────────────────┬──────────────────────────┐
│Value │ Meaning │
├──────────────────┼──────────────────────────┤
│"success" │ The service ran │
│ │ successfully and exited │
│ │ cleanly. │
├──────────────────┼──────────────────────────┤
│"protocol" │ A protocol violation │
│ │ occurred: the service │
│ │ did not take the steps │
│ │ required by its unit │
│ │ configuration │
│ │ (specifically what is │
│ │ configured in its Type= │
│ │ setting). │
├──────────────────┼──────────────────────────┤
│"timeout" │ One of the steps timed │
│ │ out. │
├──────────────────┼──────────────────────────┤
│"exit-code" │ Service process exited │
│ │ with a non-zero exit │
│ │ code; see $EXIT_CODE │
│ │ below for the actual │
│ │ exit code returned. │
├──────────────────┼──────────────────────────┤
│"signal" │ A service process was │
│ │ terminated abnormally by │
│ │ a signal, without │
│ │ dumping core. See │
│ │ $EXIT_CODE below for the │
│ │ actual signal causing │
│ │ the termination. │
├──────────────────┼──────────────────────────┤
│"core-dump" │ A service process │
│ │ terminated abnormally │
│ │ with a signal and dumped │
│ │ core. See $EXIT_CODE │
│ │ below for the signal │
│ │ causing the termination. │
├──────────────────┼──────────────────────────┤
│"watchdog" │ Watchdog keep-alive ping │
│ │ was enabled for the │
│ │ service, but the │
│ │ deadline was missed. │
├──────────────────┼──────────────────────────┤
│"start-limit-hit" │ A start limit was │
│ │ defined for the unit and │
│ │ it was hit, causing the │
│ │ unit to fail to start. │
│ │ See systemd.unit(5)'s │
│ │ StartLimitIntervalSec= │
│ │ and StartLimitBurst= for │
│ │ details. │
├──────────────────┼──────────────────────────┤
│"resources" │ A catch-all condition in │
│ │ case a system operation │
│ │ failed. │
└──────────────────┴──────────────────────────┘
This environment variable is useful to monitor failure or
successful termination of a service. Even though this
variable is available in both ExecStop= and ExecStopPost=, it
is usually a better choice to place monitoring tools in the
latter, as the former is only invoked for services that
managed to start up correctly, and the latter covers both
services that failed during their start-up and those which
failed during their runtime.
$EXIT_CODE, $EXIT_STATUS
Only defined for the service unit type, these environment
variables are passed to all ExecStop=, ExecStopPost=
processes and contain exit status/code information of the
main process of the service. For the precise definition of
the exit code and status, see wait(2). $EXIT_CODE is one of
"exited", "killed", "dumped". $EXIT_STATUS contains the
numeric exit code formatted as string if $EXIT_CODE is
"exited", and the signal name in all other cases. Note that
these environment variables are only set if the service
manager succeeded to start and identify the main process of
the service.
Table 5. Summary of possible service result variable values
┌──────────────────┬──────────────────┬──────────────────┐
│$SERVICE_RESULT │ $EXIT_CODE │ $EXIT_STATUS │
├──────────────────┼──────────────────┼──────────────────┤
│"success" │ "killed" │ "HUP", "INT", │
│ │ │ "TERM", "PIPE" │
│ ├──────────────────┼──────────────────┤
│ │ "exited" │ "0" │
├──────────────────┼──────────────────┼──────────────────┤
│"protocol" │ not set │ not set │
│ ├──────────────────┼──────────────────┤
│ │ "exited" │ "0" │
├──────────────────┼──────────────────┼──────────────────┤
│"timeout" │ "killed" │ "TERM", "KILL" │
│ ├──────────────────┼──────────────────┤
│ │ "exited" │ "0", "1", "2", │
│ │ │ "3", ..., "255" │
├──────────────────┼──────────────────┼──────────────────┤
│"exit-code" │ "exited" │ "1", "2", "3", │
│ │ │ ..., "255" │
├──────────────────┼──────────────────┼──────────────────┤
│"signal" │ "killed" │ "HUP", "INT", │
│ │ │ "KILL", ... │
├──────────────────┼──────────────────┼──────────────────┤
│"core-dump" │ "dumped" │ "ABRT", "SEGV", │
│ │ │ "QUIT", ... │
├──────────────────┼──────────────────┼──────────────────┤
│"watchdog" │ "dumped" │ "ABRT" │
│ ├──────────────────┼──────────────────┤
│ │ "killed" │ "TERM", "KILL" │
│ ├──────────────────┼──────────────────┤
│ │ "exited" │ "0", "1", "2", │
│ │ │ "3", ..., "255" │
├──────────────────┼──────────────────┼──────────────────┤
│"exec-condition" │ "exited" │ "1", "2", "3", │
│ │ │ "4", ..., "254" │
├──────────────────┼──────────────────┼──────────────────┤
│"oom-kill" │ "killed" │ "TERM", "KILL" │
├──────────────────┼──────────────────┼──────────────────┤
│"start-limit-hit" │ not set │ not set │
├──────────────────┼──────────────────┼──────────────────┤
│"resources" │ any of the above │ any of the above │
├──────────────────┴──────────────────┴──────────────────┤
│Note: the process may be also terminated by a signal │
│not sent by systemd. In particular the process may │
│send an arbitrary signal to itself in a handler for │
│any of the non-maskable signals. Nevertheless, in the │
│"timeout" and "watchdog" rows above only the signals │
│that systemd sends have been included. Moreover, using │
│SuccessExitStatus= additional exit statuses may be │
│declared to indicate clean termination, which is not │
│reflected by this table. │
└────────────────────────────────────────────────────────┘
$PIDFILE
The path to the configured PID file, in case the process is
forked off on behalf of a service that uses the PIDFile=
setting, see systemd.service(5) for details. Service code may
use this environment variable to automatically generate a PID
file at the location configured in the unit file. This field
is set to an absolute path in the file system.
For system services, when PAMName= is enabled and pam_systemd is
part of the selected PAM stack, additional environment variables
defined by systemd may be set for services. Specifically, these
are $XDG_SEAT, $XDG_VTNR, see pam_systemd(8) for details.
