добавить записи в базу данных SLAPD (Add entries to a SLAPD database)
Имя (Name)
slapadd - Add entries to a SLAPD database
Синопсис (Synopsis)
SBINDIR/slapadd [-b suffix] [-c] [-d debug-level] [-f slapd.conf]
[-F confdir] [-g] [-j lineno] [-l ldif-file] [-n dbnum]
[-o option[=value]] [-q] [-s] [-S SID] [-u] [-v] [-w]
Описание (Description)
Slapadd is used to add entries specified in LDAP Directory
Interchange Format (LDIF) to a slapd(8) database. It opens the
given database determined by the database number or suffix and
adds entries corresponding to the provided LDIF to the database.
Databases configured as subordinate of this one are also updated,
unless -g is specified. The LDIF input is read from standard
input or the specified file.
All files eventually created by slapadd will belong to the
identity slapadd is run as, so make sure you either run slapadd
with the same identity slapd(8) will be run as (see option -u in
slapd(8)), or change file ownership before running slapd(8).
Note: slapadd will also perform the relevant indexing whilst
adding the database if any are configured. For specific details,
please see slapindex(8).
Параметры (Options)
-b suffix
Use the specified suffix to determine which database to
add entries to. By default, the first database that
supports the requested operation is used. The -b cannot be
used in conjunction with the -n option.
-c enable continue (ignore errors) mode.
-d debug-level
enable debugging messages as defined by the specified
debug-level; see slapd(8) for details.
-f slapd.conf
specify an alternative slapd.conf(5) file.
-F confdir
specify a config directory. If both -f and -F are
specified, the config file will be read and converted to
config directory format and written to the specified
directory. If neither option is specified, an attempt to
read the default config directory will be made before
trying to use the default config file. If a valid config
directory exists then the default config file is ignored.
If dry-run mode is also specified, no conversion will
occur.
-g disable subordinate gluing. Only the specified database
will be processed, and not its glued subordinates (if
any).
-j lineno
Jump to the specified line number in the LDIF file before
processing any entries. This allows a load that was
aborted due to errors in the input LDIF to be resumed
after the errors are corrected.
-l ldif-file
Read LDIF from the specified file instead of standard
input.
-n dbnum
Add entries to the dbnum-th database listed in the
configuration file. The -n cannot be used in conjunction
with the -b option. To populate the config database
slapd-config(5), use -n 0 as it is always the first
database. It must physically exist on the filesystem prior
to this, however.
-o option[=value]
Specify an option with a(n optional) value. Possible
generic options/values are:
syslog=<subsystems> (see `-s' in slapd(8))
syslog-level=<level> (see `-S' in slapd(8))
syslog-user=<user> (see `-l' in slapd(8))
schema-check={yes|no}
value-check={yes|no}
The schema-check option toggles schema checking (default on);
the value-check option toggles value checking (default off).
The latter is incompatible with -q.
-q enable quick (fewer integrity checks) mode. Does fewer consistency checks
on the input data, and no consistency checks when writing the database.
Improves the load time but if any errors or interruptions occur the resulting
database will be unusable.
-s disable schema checking. This option is intended to be used when loading
databases containing special objects, such as fractional objects on a
partial consumer. Loading normal objects which do not conform to
schema may result in unexpected and ill behavior.
-S SID Server ID to use in generated entryCSN. Also used for contextCSN
if -w is set as well. Defaults to 0.
-u enable dry-run (don't write to backend) mode.
-v enable verbose mode.
-w write syncrepl context information.
After all entries are added, the contextCSN
will be updated with the greatest CSN in the database.
Ограничения (Limitations)
Your slapd(8) should not be running when you do this to ensure
consistency of the database.
slapadd may not provide naming or schema checks. It is advisable
to use ldapadd(1) when adding new entries into an existing
directory.
Примеры (Examples)
To import the entries specified in file ldif into your slapd(8)
database give the command:
SBINDIR/slapadd -l ldif
Смотри также (See also)
ldap(3), ldif(5), slapcat(8), slapindex(8), slapmodify(8),
ldapadd(1), slapd(8)
"OpenLDAP Administrator's Guide"
(http://www.OpenLDAP.org/doc/admin/)
