включить / отключить устройства и файлы для разбиения по страницам и обмена (enable/disable devices and files for paging and swapping)
Имя (Name)
swapon, swapoff - enable/disable devices and files for paging and
swapping
Синопсис (Synopsis)
swapon [options] [specialfile...]
swapoff [-va] [specialfile...]
Описание (Description)
swapon is used to specify devices on which paging and swapping
are to take place.
The device or file used is given by the specialfile parameter. It
may be of the form -L label or -U uuid to indicate a device by
label or uuid.
Calls to swapon normally occur in the system boot scripts making
all swap devices available, so that the paging and swapping
activity is interleaved across several devices and files.
swapoff disables swapping on the specified devices and files.
When the -a flag is given, swapping is disabled on all known swap
devices and files (as found in /proc/swaps or /etc/fstab).
Параметры (Options)
-a, --all
All devices marked as "swap" in /etc/fstab are made
available, except for those with the "noauto" option. Devices
that are already being used as swap are silently skipped.
-d, --discard[=policy]
Enable swap discards, if the swap backing device supports the
discard or trim operation. This may improve performance on
some Solid State Devices, but often it does not. The option
allows one to select between two available swap discard
policies:
--discard=once
to perform a single-time discard operation for the whole
swap area at swapon; or
--discard=pages
to asynchronously discard freed swap pages before they
are available for reuse.
If no policy is selected, the default behavior is to enable
both discard types. The /etc/fstab mount options discard,
discard=once, or discard=pages may also be used to enable
discard flags.
-e, --ifexists
Silently skip devices that do not exist. The /etc/fstab mount
option nofail may also be used to skip non-existing device.
-f, --fixpgsz
Reinitialize (exec mkswap) the swap space if its page size
does not match that of the current running kernel. mkswap(8)
initializes the whole device and does not check for bad
blocks.
-h, --help
Display help text and exit.
-L label
Use the partition that has the specified label. (For this,
access to /proc/partitions is needed.)
-o, --options opts
Specify swap options by an fstab-compatible comma-separated
string. For example:
swapon -o pri=1,discard=pages,nofail /dev/sda2
The opts string is evaluated last and overrides all other
command line options.
-p, --priority priority
Specify the priority of the swap device. priority is a value
between -1 and 32767. Higher numbers indicate higher
priority. See swapon(2) for a full description of swap
priorities. Add pri=value to the option field of /etc/fstab
for use with swapon -a. When no priority is defined, it
defaults to -1.
-s, --summary
Display swap usage summary by device. Equivalent to cat
/proc/swaps. This output format is DEPRECATED in favour of
--show that provides better control on output data.
--show[=column...]
Display a definable table of swap areas. See the --help
output for a list of available columns.
--output-all
Output all available columns.
--noheadings
Do not print headings when displaying --show output.
--raw
Display --show output without aligning table columns.
--bytes
Display swap size in bytes in --show output instead of in
user-friendly units.
-U uuid
Use the partition that has the specified uuid.
-v, --verbose
Be verbose.
-V, --version
Display version information and exit.
Статус выхода (Exit)
swapoff has the following exit status values since v2.36:
0
success
2
system has insufficient memory to stop swapping (OOM)
4
swapoff syscall failed for another reason
8
non-swapoff syscall system error (out of memory, ...)
16
usage or syntax error
32
all swapoff failed on --all
64
some swapoff succeeded on --all
The command swapoff --all returns 0 (all succeeded), 32 (all
failed), or 64 (some failed, some succeeded).
+ The old versions before v2.36 has no documented exit status, 0
means success in all versions.
Окружение (Environment)
LIBMOUNT_DEBUG=all
enables libmount debug output.
LIBBLKID_DEBUG=all
enables libblkid debug output.
Файлы (Files)
/dev/sd??
standard paging devices
/etc/fstab
ascii filesystem description table
Примечание (Note)
Files with holes
The swap file implementation in the kernel expects to be able to
write to the file directly, without the assistance of the
filesystem. This is a problem on files with holes or on
copy-on-write files on filesystems like Btrfs.
Commands like cp(1) or truncate(1) create files with holes. These
files will be rejected by swapon.
Preallocated files created by fallocate(1) may be interpreted as
files with holes too depending of the filesystem. Preallocated
swap files are supported on XFS since Linux 4.18.
The most portable solution to create a swap file is to use dd(1)
and /dev/zero.
Btrfs
Swap files on Btrfs are supported since Linux 5.0 on files with
nocow attribute. See the btrfs(5) manual page for more details.
NFS
Swap over NFS may not work.
Suspend
swapon automatically detects and rewrites a swap space signature
with old software suspend data (e.g., S1SUSPEND, S2SUSPEND, ...).
The problem is that if we don't do it, then we get data
corruption the next time an attempt at unsuspending is made.
История (History)
The swapon command appeared in 4.0BSD.
Смотри также (See also)
swapoff(2), swapon(2), fstab(5), init(8), fallocate(1),
mkswap(8), mount(8), rc(8)
Сообщение об ошибках (Reporting bugs)
For bug reports, use the issue tracker at
https://github.com/karelzak/util-linux/issues.
Доступность (Availability)
The swapon command is part of the util-linux package which can be
downloaded from Linux Kernel Archive
<https://www.kernel.org/pub/linux/utils/util-linux/>. This page
is part of the util-linux (a random collection of Linux
utilities) project. Information about the project can be found at
⟨https://www.kernel.org/pub/linux/utils/util-linux/⟩. If you have
a bug report for this manual page, send it to
util-linux@vger.kernel.org. This page was obtained from the
project's upstream Git repository
⟨git://git.kernel.org/pub/scm/utils/util-linux/util-linux.git⟩ on
2021-08-27. (At that time, the date of the most recent commit
that was found in the repository was 2021-08-24.) If you discover
any rendering problems in this HTML version of the page, or you
believe there is a better or more up-to-date source for the page,
or you have corrections or improvements to the information in
this COLOPHON (which is not part of the original manual page),
send a mail to man-pages@man7.org
