операции цикла событий низкого уровня (low-level event loop operations)
Дубль
(статьи:
SD_EVENT_ARMED - операции цикла событий низкого уровня )
Имя (Name)
sd_event_wait, sd_event_prepare, sd_event_dispatch,
sd_event_get_state, sd_event_get_iteration, SD_EVENT_INITIAL,
SD_EVENT_PREPARING, SD_EVENT_ARMED, SD_EVENT_PENDING,
SD_EVENT_RUNNING, SD_EVENT_EXITING, SD_EVENT_FINISHED - Low-level
event loop operations
Синопсис (Synopsis)
#include <systemd/sd-event.h>
enum {
SD_EVENT_INITIAL,
SD_EVENT_PREPARING,
SD_EVENT_ARMED,
SD_EVENT_PENDING,
SD_EVENT_RUNNING,
SD_EVENT_EXITING,
SD_EVENT_FINISHED,
};
int sd_event_prepare(sd_event *event);
int sd_event_wait(sd_event *event, uint64_t usec);
int sd_event_dispatch(sd_event *event);
int sd_event_get_state(sd_event *event);
int sd_event_get_iteration(sd_event *event, uint64_t *ret);
Описание (Description)
The low-level sd_event_prepare(), sd_event_wait() and
sd_event_dispatch() functions may be used to execute specific
phases of an event loop. See sd_event_run(3) and sd_event_loop(3)
for higher-level functions that execute individual but complete
iterations of an event loop or run it continuously.
sd_event_prepare() checks for pending events and arms necessary
timers. If any events are ready to be processed ("pending"), it
returns a positive, non-zero value, and the caller should process
these events with sd_event_dispatch().
sd_event_dispatch() dispatches the highest priority event source
that has a pending event. On success, sd_event_dispatch() returns
either zero, which indicates that no further event sources may be
dispatched and exiting of the event loop was requested via
sd_event_exit(3); or a positive non-zero value, which means that
an event source was dispatched and the loop returned to its
initial state, and the caller should initiate the next event loop
iteration by invoking sd_event_prepare() again.
In case sd_event_prepare() returned zero, sd_event_wait() should
be called to wait for further events or a timeout. If any events
are ready to be processed, it returns a positive, non-zero value,
and the events should be dispatched with sd_event_dispatch().
Otherwise, the event loop returned to its initial state and the
next event loop iteration should be initiated by invoking
sd_event_prepare() again.
sd_event_get_state() may be used to determine the state the event
loop is currently in. It returns one of the states described
below.
sd_event_get_iteration() may be used to determine the current
iteration of the event loop. It returns an unsigned 64bit integer
containing a counter that increases monotonically with each
iteration of the event loop, starting with 0. The counter is
increased at the time of the sd_event_prepare() invocation.
All five functions take, as the first argument, the event loop
object event that has been created with sd_event_new(). The
timeout for sd_event_wait() is specified in usec in microseconds.
(uint64_t) -1 may be used to specify an infinite timeout.
Состояния (State machine)
The event loop knows the following states, that may be queried
with sd_event_get_state().
SD_EVENT_INITIAL
The initial state the event loop is in, before each event
loop iteration. Use sd_event_prepare() to transition the
event loop into the SD_EVENT_ARMED or SD_EVENT_PENDING
states.
SD_EVENT_PREPARING
An event source is currently being prepared, i.e. the
preparation handler is currently being executed, as set with
sd_event_source_set_prepare(3). This state is only seen in
the event source preparation handler that is invoked from the
sd_event_prepare() call and is immediately followed by
SD_EVENT_ARMED or SD_EVENT_PENDING.
SD_EVENT_ARMED
sd_event_prepare() has been called and no event sources were
ready to be dispatched. Use sd_event_wait() to wait for new
events, and transition into SD_EVENT_PENDING or back into
SD_EVENT_INITIAL.
SD_EVENT_PENDING
sd_event_prepare() or sd_event_wait() have been called and
there were event sources with events pending. Use
sd_event_dispatch() to dispatch the highest priority event
source and transition back to SD_EVENT_INITIAL, or
SD_EVENT_FINISHED.
SD_EVENT_RUNNING
A regular event source is currently being dispatched. This
state is only seen in the event source handler that is
invoked from the sd_event_dispatch() call, and is immediately
followed by SD_EVENT_INITIAL or SD_EVENT_FINISHED as soon the
event source handler returns. Note that during dispatching of
exit event sources the SD_EVENT_EXITING state is seen
instead.
SD_EVENT_EXITING
Similar to SD_EVENT_RUNNING but is the state in effect while
dispatching exit event sources. It is followed by
SD_EVENT_INITIAL or SD_EVENT_FINISHED as soon as the event
handler returns.
SD_EVENT_FINISHED
The event loop has exited. All exit event sources have run.
If the event loop is in this state it serves no purpose
anymore, and should be freed.
A simplified flow chart of the states and the calls to transition
between them is shown below. Note that SD_EVENT_PREPARING,
SD_EVENT_RUNNING and SD_EVENT_EXITING are not shown here.
INITIAL -<---<---<---<---<---<---<---<---<---<---<---<---\
| |
| ^
| |
v ret == 0 |
sd_event_prepare() >--->--->--->--->- ARMED |
| | ^
| ret > 0 | |
| | |
v v ret == 0 |
PENDING <---<---<---<---<---< sd_event_wait() >--->--->--+
| ret > 0 ^
| |
| |
v |
sd_event_dispatch() >--->--->--->--->--->--->--->--->--->--->/
| ret > 0
| ret == 0
|
v
FINISHED
Возвращаемое значение (Return value)
On success, these functions return 0 or a positive integer. On
failure, they return a negative errno-style error code. In case
of sd_event_prepare() and sd_event_wait(), a positive, non-zero
return code indicates that events are ready to be processed and
zero indicates that no events are ready. In case of
sd_event_dispatch(), a positive, non-zero return code indicates
that the event loop returned to its initial state and zero
indicates the event loop has exited. sd_event_get_state()
returns a positive or zero state on success.
Errors
Returned errors may indicate the following problems:
-EINVAL
The event parameter is invalid or NULL.
-EBUSY
The event loop object is not in the right state.
-ESTALE
The event loop is already terminated.
-ECHILD
The event loop has been created in a different process.
Other errors are possible, too.
Примечание (Note)
These APIs are implemented as a shared library, which can be
compiled and linked to with the libsystemd pkg-config(1) file.
Смотри также (See also)
systemd(1), sd_event_new(3), sd_event_add_io(3),
sd_event_add_time(3), sd_event_add_signal(3),
sd_event_add_child(3), sd_event_add_inotify(3),
sd_event_add_defer(3), sd_event_run(3), sd_event_get_fd(3),
sd_event_source_set_prepare(3)
